Emc connection utility

To configure the number of hot spares, or configure a storage pool and RAID group, select the appropriate pool and click Configure Disks. First browse to the Management Settings page of the Settings drop down menu. To change the language displayed in the Connection Utility, select the desired language from the list under Change language: The system management ports support both IPv4 and IPv6. Fibre Channel or Ethernet.

Uploader: JoJolmaran
Date Added: 17 December 2007
File Size: 65.37 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 47184
Price: Free* [*Free Regsitration Required]





Repeat the process for any additional DAEs. This process may take up to 10 minutes.

EMC Unity Initialization – Victor Virtualization

At the end of the power-up process, the SP Fault LED blinks in intervals of amber for one second and then blue for three seconds, indicating that the system is ready to run the Connection Utility. To manually assign a static IP address for the storage system management port, you must install and run the Connection Utility on a Windows-based computer.

Some considerations when creating storage pools; typically emd want to configure less storage pools to reduce utulity and increase flexibility, however configuring multiple storage pools may be required if you want to separate workloads.

If you are unable to run the Connection Utility from the same subnet, you can still manually configure the connection. You will need to make design decisions based on your environment around storage pool capacities and configured RAID protection.

EMC Community Network - DECN: VNX Connection Utility

The tabs secure and support the rear of the enclosure, the front is secured using 2 x M5 screws on each side. To change the language displayed in the Connection Utility, select the desired language from the list under Change language: The Initial Configuration Wizard launches the first time you login. For larger configurations with high drive counts EMC does not recommend using the system drives as heavy client workload may slow down management operations does not apply to all-flash.

To configure the number of hot spares, or configure a storage pool and RAID group, select the appropriate pool and click Configure Disks.

EMC VNXe Setup Guide

To access the web UI for setup we have a couple of options for automatic or manual IP addressing. Set up a management interface connection Unity Family technical documentation.

The storage system will automatically detect the USB drive and apply the network connection information. Log in to Unisphere using the default credentials admin Password Email required Address never made public.

View All Search Results. Fill in your details below or click an icon to log in: This can be achieved from the Settings drop down menu, and selecting Update software. Push the key tabs and adaptors into the rear mounting holes until the spring clips snap into place.

Run the Connection Utility from a conndction attached to the same subnet as your storage system. Itility self explanatory wizard guides you through the basic setup of the array, any settings you skip here can be configured later through the appropriate menus. Unboxing The VNXe base comes with the following: Front end ports need to be connected and configured symmetrically across both storage processors to facilitate high availability.

Front bezel for DAE. Storage pools are configured under SystemStorage Pools. Secure the rear of the rail using 1 x M5 screw on each side. Serial number of your storage system. The Connection Utility automatically sets the displayed language based on the settings of the computer.

Perform the following steps to automatically assign an IP address to your storage system management port:. Once the configuration wizard is complete you will be returned to the home dashboard.

This computer will be used to continue setting up your system and must be on the same subnet as the storage system to complete the initialization. Notify me of connection comments via email. NAS ports should also be configured with LACP grouped per storage processor, to provide path redundancy and performance improvements. Assigning an IP address to a storage system management port dynamically requires the following:

3 thoughts on “Emc connection utility”

  1. I can not participate now in discussion - it is very occupied. I will return - I will necessarily express the opinion on this question.

  2. In my opinion you commit an error. I can prove it. Write to me in PM, we will discuss.

Leave a Reply

Your email address will not be published. Required fields are marked *